Time Interleaved Analog To Digital Converters

Time-interleaved Analog-to-Digital Converters describes the research performed on low-power time-interleaved ADCs. A detailed theoretical analysis is made of the time-interleaved Track & Hold, since it must be capable of handling signals in the GHz range with little distortion, and minimal power consumption. Timing calibration is not attractive, therefore design techniques are presented which do not require timing calibration. The design of power efficient sub-ADCs is addressed with a theoretical analysis of a successive approximation converter and a pipeline converter. It turns out that the first can consume about 10 times less power than the latter, and this conclusion is supported by literature. Time-interleaved Analog-to-Digital Converters describes the design of a high performance time-interleaved ADC, with much attention for practical design aspects, aiming at both industry and research. Measurements show best-inclass performance with a sample-rate of 1.8 GS/s, 7.9 ENOBs and a power efficiency of 1 pJ/conversion-step.

This book describes techniques for time-interleaving a number of analog-to-digital data converters to achieve demanding bandwidth requirements. Readers will benefit from the presentation of a low-power solution that can be used in actual products, while alleviating the time-varying signal artifacts that typically arise when implementing such a system architecture.

Modern complementary metal oxide semiconductor (CMOS) digital-to-analog converters (DACs) are limited in their bandwidth due to technological constraints. These limitations can be overcome by parallel DAC architectures, which are called interleaving concepts. Christian Schmidt analyzes the limitations and the potential of two innovative DAC interleaving concepts to provide the basis for a practical implementation: the analog multiplexing DAC (AMUX-DAC) and the frequency interleaving DAC (FI-DAC). He presents analytical and discrete-time models as a theoretical foundation and develops digital signal processing (DSP) algorithms to compensate the analog impairments. Further, he quantifies the impact of various limiting parameters with numerical simulations and verifies both concepts in laboratory experiments. About the Author: Christian Schmidt works at the Fraunhofer Heinrich-Hertz-Institute, Berlin, Germany, on innovative solutions for broadband signal generation in the field of optical communications. The studies for his dissertation were carried out at the Technische Universität Berlin and at the Fraunhofer Heinrich-Hertz-Institute, both Berlin, Germany.

This book shows that digitally assisted analog to digital converters are not the only way to cope with poor analog performance caused by technology scaling. It describes various analog design techniques that enhance the area and power efficiency without employing any type of digital calibration circuitry. These techniques consist of self-biasing for PVT enhancement, inverter-based design for improved speed/power ratio, gain-of-two obtained by voltage sum instead of charge redistribution, and current-mode reference shifting instead of voltage reference shifting. Together, these techniques allow enhancing the area and power efficiency of the main building blocks of a multiplying digital-to-analog converter (MDAC) based stage, namely, the flash quantizer, the amplifier, and the switched capacitor network of the MDAC. Complementing the theoretical analyses of the various techniques, a power efficient operational transconductance amplifier is implemented and experimentally characterized. Furthermore, a medium-low resolution reference-free high-speed time-interleaved pipeline ADC employing all mentioned design techniques and circuits is presented, implemented and experimentally characterized. This ADC is said to be reference-free because it precludes any reference voltage, therefore saving power and area, as reference circuits are not necessary. Experimental results demonstrate the potential of the techniques which enabled the implementation of area and power efficient circuits.

Analog-to-Digital Converters (ADCs) play an important role in most modern signal processing and wireless communication systems where extensive signal manipulation is necessary to be performed by complicated digital signal processing (DSP) circuitry. This trend also creates the possibility of fabricating all functional blocks of a system in a single chip (System On Chip - SoC), with great reductions in cost, chip area and power consumption. However, this tendency places an increasing challenge, in terms of speed, resolution, power consumption, and noise performance, in the design of the front-end ADC which is usually the bottleneck of the whole system, especially under the unavoidable low supply-voltage imposed by technology scaling, as well as the requirement of battery operated portable devices. Generalized Low-Voltage Circuit Techniques for Very High-Speed Time-Interleaved Analog-to-Digital Converters will present new techniques tailored for low-voltage and high-speed Switched-Capacitor (SC) ADC with various design-specific considerations.

Need to get up to speed quickly on the latest advances in high performance data converters? Want help choosing the best architecture for your application? With everything you need to know about the key new converter architectures, this guide is for you. It presents basic principles, circuit and system design techniques and associated trade-offs, doing away with lengthy mathematical proofs and providing intuitive descriptions upfront. Everything from time-to-digital converters to comparator-based/zero-crossing ADCs is covered and each topic is introduced with a short summary of the essential basics. Practical examples describing actual chips, along with extensive comparison between architectural or circuit options, ease architecture selection and help you cut design time and engineering risk. Trade-offs, advantages and disadvantages of each option are put into perspective with a discussion of future trends, showing where this field is heading, what is driving it and what the most important unanswered questions are.

This textbook is appropriate for use in graduate-level curricula in analog-to-digital conversion, as well as for practicing engineers in need of a state-of-the-art reference on data converters. It discusses various analog-to-digital conversion principles, including sampling, quantization, reference generation, nyquist architectures and sigma-delta modulation. This book presents an overview of the state of the art in this field and focuses on issues of optimizing accuracy and speed, while reducing the power level. This new, third edition emphasizes novel calibration concepts, the specific requirements of new systems, the consequences of 22-nm technology and the need for a more statistical approach to accuracy. Pedagogical enhancements to this edition include additional, new exercises, solved examples to introduce all key, new concepts and warnings, remarks and hints, from a practitioner's perspective, wherever appropriate. Considerable background information and practical tips, from designing a PCB, to lay-out aspects, to trade-offs on system level, complement the discussion of basic principles, making this book a valuable reference for the experienced engineer.