Power Processing Circuits Design

Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

This book describes the design of CMOS circuits for ultra-low power consumption including analog, radio frequency (RF), and digital signal processing circuits (DSP). The book addresses issues from circuit and system design to production design, and applies the ultra-low power circuits described to systems for digital hearing aids and capsule endoscope devices. Provides a valuable introduction to ultra-low power circuit design, aimed at practicing design engineers; Describes all key building blocks of ultra-low power circuits, from a systems perspective; Applies circuits and systems described to real product examples such as hearing aids and capsule endoscopes.

Power Processing Circuits Design seamlessly infuses important mathematical models and approaches into the optimization of power processing circuits and linear systems. The work unites a constellation of challenging mathematical topics centered on differential equations, linear algebra and implicit functions, with multiple perspectives from electrical, mathematical and physical viewpoints, including power handling components, power filtering and power regulation. Power applications covered encompass first order RC and RL, second order RLC circuits with periodic drives, constant current source, close-loop feedback practices, control loop types, linear regulator, switch-mode regulator and rotation control. Outlines the physical meaning of differential forms and integral forms in designing circuits for power applications Delivers techniques to set up linear algebraic matrix representations of complex circuits Explores key approaches obtaining steady state and describes methods using implicit functions for close-loop representation Describes how to implement vector representation of rotational driving sources Supplemented by MATLAB implementations

This book presents state-of-the-art analog and power management IC design techniques for various wireless power transfer (WPT) systems. To create elaborate power management solutions, circuit designers require an in-depth understanding of the characteristics of each converter and regulator in the power chain. This book addresses WPT design issues at both system- and circuit-level, and serves as a handbook offering design insights for research students and engineers in the integrated power electronics area.

This book will describe ultra low-power, integrated circuits and systems designed for the emerging field of neural signal recording and processing, and wireless communication. Since neural interfaces are typically implanted, their operation is highly energy-constrained. This book introduces concepts and theory that allow circuit operation approaching the fundamental limits. Design examples and measurements of real systems are provided. The book will describe circuit designs for all of the critical components of a neural recording system, including: Amplifiers which utilize new techniques to improve the trade-off between good noise performance and low power consumption. Analog and mixed-signal circuits which implement signal processing tasks specific to the neural recording application: Detection of neural spikes Extraction of features that describe the spikes Clustering, a machine learning technique for sorting spikes Weak-inversion operation of analog-domain transistors, allowing processing circuits that reduce the requirements for analog-digital conversion and allow low system-level power consumption. Highly-integrated, sub-mW wireless transmitter designed for the Medical Implant Communications Service (MICS) and ISM bands.

This book tackles challenges for the design of analog integrated circuits that operate from ultra-low power supply voltages (down to 0.5V). Coverage demonstrates the signal processing circuit and circuit biasing approaches through the design of operational transconductance amplifiers (OTAs). These amplifiers are then used to build analog system functions including continuous time filter and a sample and hold amplifier.

Switched-Current Signal Processing and A/D Conversion Circuits: Design and Implementation describes the design and implementation of switched-current (SI) circuits with emphasis on signal processing and data-conversion applications. The work includes theoretical analysis, high-level and circuit-level simulation results as well as measurement results from a few of the author's circuit implementations. An extensive overview of the SI field of research is also given. The book contains an extensive overview of the switched-current field of research, and can therefore be used as a quick-reference to the field. The description of each design example has been organized to describe the entire design flow from system level design and simulation, to circuit simulation, layout and measurement as accurately as possible. Thus it is possible to follow each step in the design process. Switched-Current Signal Processing and A/D Conversion Circuits: Design and Implementation is an invaluable reference for researchers and circuit designers working with one-chip mixed-signal system solutions, and low-voltage analog CMOS design. It will also be appreciated by anyone requiring a quick overview of what has been done in the SI field.

This book presents theory, design methods and novel applications for integrated circuits for analog signal processing. The discussion covers a wide variety of active devices, active elements and amplifiers, working in voltage mode, current mode and mixed mode. This includes voltage operational amplifiers, current operational amplifiers, operational transconductance amplifiers, operational transresistance amplifiers, current conveyors, current differencing transconductance amplifiers, etc. Design methods and challenges posed by nanometer technology are discussed and applications described, including signal amplification, filtering, data acquisition systems such as neural recording, sensor conditioning such as biomedical implants, actuator conditioning, noise generators, oscillators, mixers, etc. Presents analysis and synthesis methods to generate all circuit topologies from which the designer can select the best one for the desired application; Includes design guidelines for active devices/elements with low voltage and low power constraints; Offers guidelines for selecting the right active devices/elements in the design of linear and nonlinear circuits; Discusses optimization of the active devices/elements for process and manufacturing issues of nanometer technology.