Digital Signal Processing In Power Electronics Control Circuits

Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

Many digital control circuits in current literature are described using analog transmittance. This may not always be acceptable, especially if the sampling frequency and power transistor switching frequencies are close to the band of interest. Therefore, a digital circuit is considered as a digital controller rather than an analog circuit. This helps to avoid errors and instability in high frequency components. Digital Signal Processing in Power Electronics Control Circuits covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book bridges the gap between power electronics and DSP. The following realizations of digital control circuits are considered: digital signal processors, microprocessors, microcontrollers, programmable digital circuits. Discussed in this book is signal processing, starting from analog signal acquisition, through its conversion to digital form, methods of its filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing: an active power filter and a digital class D power amplifier. The major benefit to readers is the acquisition of specific knowledge concerning discussions on the processing of signals from voltage or current sensors using a digital signal processor and to the signals controlling the output inverter transistors. Included are some Matlab examples for illustration of the considered problems.

This revised and extended second edition covers problems concerning the design and realization of digital control algorithms for power electronics circuits using digital signal processing (DSP) methods. This book discusses signal processing, starting from analog signal acquisition, through conversion to digital form, methods of filtration and separation, and ending with pulse control of output power transistors. The book is focused on two applications for the considered methods of digital signal processing, a three-phase shunt active power filter and a digital class-D audio power amplifier. The book bridges the gap between power electronics and digital signal processing. Many control algorithms and circuits for power electronics in the current literature are described using analog transmittances. This may not always be acceptable, especially if half of the sampling frequencies and half of the power transistor switching frequencies are close to the band of interest. Therefore in this book, a digital circuit is treated as a digital circuit with its own peculiar characteristics, rather than an analog circuit. This helps to avoid errors and instability. This edition includes a new chapter dealing with selected problems of simulation of power electronics systems together with digital control circuits. The book includes numerous examples using MATLAB and PSIM programs.

The purpose of this project has been to study, operate and program the 32-bit 150MIPS TMS320F2812 DSP developed by Texas Instruments Inc. In addition, it has also been a goal to implement fast estimation techniques for control of resonant converters. For this purpose, PWM signals that are generated using this DSP are used. The demands on the system and the hardware to solve the problem were already decided when I started the work. The algorithms were programmed in C/C++ language, compiled, debugged and transferred to the DSP development board in a compiling and simulation tool (downloader), called CCS (Code Composer Studio v2), also provided by Texas Instruments. In the first chapters of this study I give general information about control systems, digital signal processors, digital signal processing and the DSP used in this work. The following chapters tell about PWM, how to configure the PWM outputs and some examples related with PWM signals are given. After a short review of series resonant converters, I presented the last example implemented in this project. I conclude with a summary and provide some hints of future work.

Digital Signal Processing in Power System Protection and Control bridges the gap between the theory of protection and control and the practical applications of protection equipment. Understanding how protection functions is crucial not only for equipment developers and manufacturers, but also for their users who need to install, set and operate the protection devices in an appropriate manner. After introductory chapters related to protection technology and functions, Digital Signal Processing in Power System Protection and Control presents the digital algorithms for signal filtering, followed by measurement algorithms of the most commonly-used protection criteria values and decision-making methods in protective relays. A large part of the book is devoted to the basic theory and applications of artificial intelligence techniques for protection and control. Fuzzy logic based schemes, artificial neural networks, expert systems and genetic algorithms with their advantages and drawbacks are discussed. AI techniques are compared and it is also shown how they can be combined to eliminate the disadvantages and magnify the useful features of particular techniques. The information provided in Digital Signal Processing in Power System Protection and Control can be useful for protection engineers working in utilities at various levels of the electricity network, as well as for students of electrical engineering, especially electrical power engineering. It may also be helpful for other readers who want to get acquainted with and to apply the filtering, measuring and decision-making algorithms for purposes other than protection and control, everywhere fast and on-line signal analysis is needed for proper functioning of the apparatus.

Resource added for the Electronics/Biomedical Technology program 106051.

This book is a collection of tutorial-like chapters on all core topics of signals and systems and the electronic circuits. All the topics dealt with in the book are parts of the core syllabi of standard programs in Electrical Engineering, Electrical and Computer Engineering, and Electronics and Telecommunication Engineering domains. This book is intended to serve as a secondary reader or supplementary text for core courses in the area of signals and systems, electronic circuits, and analog and digital signal processing. When studying or teaching a particular topic, the students and instructors of such courses would find it interesting and worthwhile to study the related tutorial chapter in this book in order to enhance their understanding of the fundamentals, simplification of procedures, alternative approaches and relation to other associated topics. In addition, the book can also be used as a primary or secondary text in short-term or refresher courses, and as a self-study guide for professionals wishing to gain a comprehensive review of the signals and systems domain.

The purpose of this book is to describe the theory of Digital Power Electronics and its applications. The authors apply digital control theory to power electronics in a manner thoroughly different from the traditional, analog control scheme. In order to apply digital control theory to power electronics, the authors define a number of new parameters, including the energy factor, pumping energy, stored energy, time constant, and damping time constant. These parameters differ from traditional parameters such as the power factor, power transfer efficiency, ripple factor, and total harmonic distortion. These new parameters result in the definition of new mathematical modeling: • A zero-order-hold (ZOH) is used to simulate all AC/DC rectifiers. • A first-order-hold (FOH) is used to simulate all DC/AC inverters. • A second-order-hold (SOH) is used to simulate all DC/DC converters. • A first-order-hold (FOH) is used to simulate all AC/AC (AC/DC/AC) converters. Presents most up-to-date methods of analysis and control algorithms for developing power electronic converters and power switching circuits Provides an invaluable reference for engineers designing power converters, commercial power supplies, control systems for motor drives, active filters, etc. Presents methods of analysis not available in other books