Transition Turbulence And Combustion Modelling

This single-volume work gives an introduction to the fields of transition, turbulence, and combustion modeling of compressible flows and provides the physical background for today’s modeling approaches in these fields. It presents basic equations and discusses fundamental aspects of hydrodynamical instability.

Turbulent combustion sits at the interface of two important nonlinear, multiscale phenomena: chemistry and turbulence. Its study is extremely timely in view of the need to develop new combustion technologies in order to address challenges associated with climate change, energy source uncertainty, and air pollution. Despite the fact that modeling of turbulent combustion is a subject that has been researched for a number of years, its complexity implies that key issues are still eluding, and a theoretical description that is accurate enough to make turbulent combustion models rigorous and quantitative for industrial use is still lacking. In this book, prominent experts review most of the available approaches in modeling turbulent combustion, with particular focus on the exploding increase in computational resources that has allowed the simulation of increasingly detailed phenomena. The relevant algorithms are presented, the theoretical methods are explained, and various application examples are given. The book is intended for a relatively broad audience, including seasoned researchers and graduate students in engineering, applied mathematics and computational science, engine designers and computational fluid dynamics (CFD) practitioners, scientists at funding agencies, and anyone wishing to understand the state-of-the-art and the future directions of this scientifically challenging and practically important field.

Turbulence is one of the key issues in tackling engineering flow problems. As powerful computers and accurate numerical methods are now available for solving the flow equations, and since engineering applications nearly always involve turbulence effects, the reliability of CFD analysis depends increasingly on the performance of the turbulence models. This series of symposia provides a forum for presenting and discussing new developments in the area of turbulence modelling and measurements, with particular emphasis on engineering-related problems. The papers in this set of proceedings were presented at the 5th International Symposium on Engineering Turbulence Modelling and Measurements in September 2002. They look at a variety of areas, including: Turbulence modelling; Direct and large-eddy simulations; Applications of turbulence models; Experimental studies; Transition; Turbulence control; Aerodynamic flow; Aero-acoustics; Turbomachinery flows; Heat transfer; Combustion systems; Two-phase flows. These papers are preceded by a section containing 6 invited papers covering various aspects of turbulence modelling and simulation as well as their practical application, combustion modelling and particle-image velocimetry.

These two volumes are concerned with current technologically important issues of transition, turbulence and combustion. Topics covered in transition include linear and nonlinear stability, direct and large-eddy simulation and phenomenological modelling of the transition zone. In turbulence, interest was focused on second-order closures and the formulation of near-wall corrections to existing high Reynolds number models, and closure model development based on turbulent flow structures and RNG theory. Topics covered in combustion include counterflow diffusion flames, development of novel mixing enhancement techniques for non-premixed combustion, and methods of modelling the interaction between turbulence and chemical kinetics. This collection of papers from leading researchers represents as yet unpublished state-of-the-art research, resulting in a very valuable tool for scientists and students working in areas of turbulence, transition and combustion.

These two volumes contain the proceedings of the Workshop on Transition, Turbulence and Combustion, sponsored by the Insti tute for Computer Applications in Science and Engineering (ICASE) and the NASA Langley Research Center (LaRC), during June 7 to July 2, 1993. Volume I contains the contributions from the transi tion research, and Volume II contains the contributions from both the turbulence and combustion research. This is the third workshop in the series on the subject. The first was held in 1989, the second in 1991, and their proceedings were published by Springer-Verlag under the titles "Instability and Transition" (edited by M. Y. Hussaini and R. G. Voigt) and "Instability, Transition and Turbulence" (edited by M. Y. Hussaini, A. Kumar and C. L. Streett) respectively. The objectives of these workshops are to expose the academic community to current technologically important issues of transition, turbulence and combustion, and to acquaint the academic commu nity with the unique combination of theoretical, computational and experimental capabilities at LaRC. It is hoped these will foster con tinued interactions, and accelerate progress in elucidating the funda mental phenomena of transition, turbulence and combustion. The research areas of interest in transition covered the full range of the subject: linear and nonlinear stability, direct and large-eddy simulation and phenomenological modeling of the transition zone.

These two volumes are concerned with current technologically important issues of transition, turbulence and combustion. Topics covered in transition include linear and nonlinear stability, direct and large-eddy simulation and phenomenological modelling of the transition zone. In turbulence, interest was focused on second-order closures and the formulation of near-wall corrections to existing high Reynolds number models, and closure model development based on turbulent flow structures and RNG theory. Topics covered in combustion include counterflow diffusion flames, development of novel mixing enhancement techniques for non-premixed combustion, and methods of modelling the interaction between turbulence and chemical kinetics. This collection of papers from leading researchers represents as yet unpublished state-of-the-art research, resulting in a very valuable tool for scientists and students working in areas of turbulence, transition and combustion.

The workshop concentrated on the following turbulence test cases: T1 Boundary layer in an S-shaped duct; T2 Periodic array of cylinders in a channel; T3 Transition in a boundary layer under the influence of free-stream turbulence; T4 & T5: Axisymmetric confined jet flows.

Proceedings of the world renowned ERCOFTAC (International Symposium on Engineering Turbulence Modelling and Measurements). The proceedings include papers dealing with the following areas of turbulence: · Eddy-viscosity and second-order RANS models · Direct and large-eddy simulations and deductions for conventional modelling · Measurement and visualization techniques, experimental studies · Turbulence control · Transition and effects of curvature, rotation and buoyancy on turbulence · Aero-acoustics · Heat and mass transfer and chemically reacting flows · Compressible flows, shock phenomena · Two-phase flows · Applications in aerospace engineering, turbomachinery and reciprocating engines, industrial aerodynamics and wind engineering, and selected chemical engineering problems Turbulence remains one of the key issues in tackling engineering flow problems. These problems are solved more and more by CFD analysis, the reliability of which depends strongly on the performance of the turbulence models employed. Successful simulation of turbulence requires the understanding of the complex physical phenomena involved and suitable models for describing the turbulent momentum, heat and mass transfer. For the understanding of turbulence phenomena, experiments are indispensable, but they are equally important for providing data for the development and testing of turbulence models and hence for CFD software validation. As in other fields of Science, in the rapidly developing discipline of turbulence, swift progress can be achieved only by keeping up to date with recent advances all over the world and by exchanging ideas with colleagues active in related fields.