Environmental Chemistry Water And Soil Pollution

INTRODUCTION Environmental science is the systematic study of the interaction of two worlds. The word ‘Environment’ is derived from an old French word ‘environ’ meaning ‘encircle’. The environment consists of four segments: atmosphere, hydrosphere, lithosphere and biosphere. Among all of substances, water is a marvelous substance on earth. Water is one of the abundantly available substances in nature. Water is essential for all kinds of life and is the medium in which all living processes occur. Water is renewable source, but renewable takes time. The hydrological cycle constantly purifies and redistributes fresh water on landmasses, providing endless renewable resource. At present, there are many environmental issues, which have grown in size and complexity day by day, threatening the survival of mankind and all living organisms on earth. Unfortunately, with progress in science and technology, man has been dumping waste material into atmosphere and causing pollution. Environmental pollution can be divided among the categories of water, air and soil pollution. Emission of pollutants in air, water and soil has caused considerable damage to our environment. Water pollution disturbs the normal uses of water for irrigation, agriculture, industries, public water supply and aquatic life. Most of the human activities produce liquid effluents, which are the prime cause of water pollution. Rapid increase in population, intensive agriculture, growing industrialization and urbanization has resulted in progressive deterioration in the quality of water in our natural reservoirs. Most of the water related diseases are some way or other concerned with the polluted water supply. Water borne infections diseases like cholera, dysentery, typhoid, jaundice and worm infection are still the major public health problems in developing countries. Another substance, which plays a very important role, is soil as it produces food for human beings and animals. Soil is a complex of physical and biological systems, which give support to the plants and supplies water and essential nutrients to them. It is the main reservoir of the minerals essential for normal growth of the plants. The soil consists of four major components, i.e. mineral matter, organic matter, soil air and soil water. All these components cannot be separated with much satisfaction because they are present very intimately mixed with each other. With careful husbandry, soil can be replenished and renewed indefinitely. Hazardous chemicals heavily pollute soil day by day. Disposal of industrial waste is the major problem responsible for soil pollution. These waste products are also tipped on soil, enhancing the extent of soil pollution. As a result, hazardous chemicals can enter into human food chain from the soil or water, disturb the biochemical process and finally lead to serious effects on living organisms. Large-scale soil and water pollution is one of the primary factors behind the high prevalence of soil and water borne diseases. Soil degradation can reduce the quality of our food, whereas deforestation can reduce the availability plants to make current medicines and medicines for the future. Heavy metal pollution has also a serious impact. Metal pollution can affect all environments but its effects most long lasting in soil. Drinking is one of the major routes of intake of heavy metals by the human body. Soil contamination should be a primary concern in India, because the country relies heavily on agriculture. Toxic metal is the one, which is neither essential nor beneficial but exhibits a positive catastrophic effect on normal metabolic function even when present in small amounts and may, at times, be responsible for permanent disorders or malfunctioning of organ system leading finally to death. This BOOK consists of five chapters. CHAPTER 1: INTRODUCTION This chapter is divided into two parts: 1A: WATER This part contains Introduction of Water, Properties of Water, Major Water Compartments, Types & Forms of Water, Water and its Significance, Potability of Water, Water Consumption Pattern & Demand, Water Resources, Water Quality for Irrigation and Ground Water Quality Status in Rajasthan. 1B: SOIL & VEGETATION This part contains Introduction of Soil, What is Soil?, Composition of Soil, Process of Soil Formation, Soil Profile, Soil Texture, Types of Soil, Soil pH, Life on Soil, Macro and Micro Plant Nutrients, Functions of Various Nutrients and Agricultural Status w.r.t. Soil. CHAPTER 2: WATER & SOIL POLLUTION This chapter is divided into two parts: 2A: WATER POLLUTION (i) This part contains Environmental Pollution, Water Pollution, Causes of Water Pollution, Sources of Water Pollution, Types of Water Pollution, Classification of Pollutants, Types of Pollutants, Characteristics of Fresh Water, Chemical Characteristics of Water, Characteristics of Industrial Wastes, Control of Water Pollution, Diseases Caused by Water Pollution, Various Effluents and Their Effects on Aquatic Organisms, Fluoridation and Defluoridation of Water, Water Management, Water Pollution in India and Water Pollution in Rajasthan. (ii) 2B: SOIL POLLUTION This part contains Soil Pollution, Sources of Soil Pollution, Diseases Caused by Soil Pollution, Control of Soil Pollution, Heavy Metal Toxicology, Sources of Heavy Metals and Environment Friendly Technologies. CHAPTER 3: METHODS & METHODOLOGY METHODOLOGY FOR WATER Wastewater samples were collected from eleven different sites from the ‘AMANISHAH NALA’ and groundwater (Hand pump) samples were taken from nine different vicinal locations of various industrial sites. Samples were collected in good quality screw–capped polyethylene bottles of one litre capacity, labeled properly and analyzed in laboratory for their all physico–chemical parameters. Monitoring was done during the three seasons (pre-monsoon, during monsoon and post-monsoon) throughout the two-years from different industrial areas and adjacent places of Jaipur city (June, 2002 to May, 2004). Various physical parameters like pH, EC, DO and TDS, which are important to evaluate the suitability of wastewater for irrigation, were determined on the site with the help of digital portable water analyzer kit (CENTURY–CK–710). For rest of the analysis, water samples were preserved and bought to the laboratory. The chemical analysis carried out for BOD by incubation method, COD by KMnO4 method, Calcium (Ca2+), Magnesium (Mg2+), Chloride (Cl–), Sulphate (SO42–), Carbonate (CO32–) and Bicarbonate (HCO3–) by volumetric titration methods; while Fluoride (F–) by spectrophotometric (AIMIL–C160–80314) & ion selective electrode method and Nitrate (NO3–) by spectrophotometric (ELICO–CL–54D) method; Sodium (Na+), Potassium (K+) by flamephotometry (ELICO–CL–220) and heavy metals by AAS. In order to estimate the quality of the groundwater for drinking purposes, an indexing system, Water Quality Index (WQI), based on Adak and Purohit(20), was determined. Evaluation of the quality of wastewater on the basis of percent sodium (%Na) is excellent, was determined. Quantitatively, United States Salinity Laboratory (USSL) proposed, for the first time, a better index called ‘Sodium Absorption Ratio (SAR)’, was determined. Sodium hazard of irrigation water can be well understood by knowing SAR. There is a significant correlation between SAR values of irrigation water and the extent to which sodium is absorbed by the soil. METHODOLOGY FOR SOIL Soil samples were collected from thirteen different vicinal locations of various industrial sites where industrial wastewater use for irrigation. Samples were collected in good quality polyethylene bags, labeled properly and analyzed in laboratory for their all parameters. Monitoring was done during the four intervals throughout the year from different vicinal locations of various industrial sites of Jaipur city where industrial wastewater use for irrigation (April, 2004 to March, 2005). Soil samples may be analyzed for the following parameters like: pH, EC, Organic Carbon, Nitrogen, Phosphorous, Potassium, Fe, Zn, Cu, Mn, etc. CHAPTER 4: RESULTS AND DISCUSSION This chapter is divided into three parts: 4A: WATER FOR DOMESTIC PURPOSES In these sites, positive correlation between surface and ground water was recognized. The groundwater near solid waste and liquid waste disposal sites was polluted, whereas the groundwater away from disposal sites was not much affected. The values obtained were compared with standards of ISI, ICMR and WHO. From the observations, it may inferred that the concentration of pH, EC, Ca2+, Na+, K+, Mg2+, SO42–, CO32–, HCO32–, Cl–, DO and BOD are within permissible limits of ISI, ICMR & WHO but NO3–, TDS, TH, COD and WQI values show the poor water quality in most of the studied groundwater samples taken from vicinal locations of various industrial sites. Concentrations of all heavy metals like Cr, Cu, Cd, Mn, Ni, Pb, Fe, As & Zn are within permissible limits. Higher concentrations of Zn in very few samples have been observed. WQI values of these samples were ranging from 35.08 to 268.78 which means that only 37.5% sample’s water were fit for human consumption directly, but 62.5% water of all sources can be used for domestic consumption after appropriate treatment whereas remaining 37.5% water of samples were of very poor quality and was not recommended for domestic purposes. So it may be accomplished with the help of WQI that the water of the various samples were unfit for drinking purpose without further treatment (mainly disinfections). It may be concluded that the general characteristics of groundwater samples from the study area classify the water under moderate category and are tolerable for household and commercial purposes However, high WQI and COD values suggest purification may be necessary for domestic consumption. 4B: WATER FOR IRRIGATION PURPOSES The suitability of groundwater and wastewater for irrigation depends upon its mineral constituents. The salts present in the water, besides affecting the growth of the plants directly also affect the soil structure, permeability and aeration, which indirectly affect the plant growth. Jaipur is undergoing rapid urbanization and industrialization. Wastewater generated from various industries discharged into ‘AMANISHAH NALA’ where this water is used for irrigation purpose. The values obtained were compared with standards of ISI, ICMR and WHO. The concentrations of pH, Na+, K+, Ca2+, Mg2+, SO42–, CO32–, HCO3–, TH, Cl–, NO3–, Oil & Grease, DO and F– are within permissible limits in both groundwater and wastewater but definite contaminations with special reference to EC, TDS, BOD and COD in wastewater have been observed, calls for at least primary treatment of wastewater before being used for irrigation. High EC and TDS values reflect greater salinity of water and it cannot be suitable for irrigation under ordinary conditions. There was also a significant correlation between SAR values of irrigation water and the extent to which sodium is absorbed by the soil. No excellent conclusion can be drawn to observed values but general conclusion can be drawn as: The general characteristics of groundwater and industrial wastewater samples from the study area classify the water under moderate category and are good for household, irrigation and commercial purposes and results of suitability evaluation indicate that there is no major pollution hazard in wastewater of AMANISHAH NALA. However, high BOD and COD values suggest purification may be necessary for sensitive crops and human consumption. 4C: SOIL FOR AGRICULTURAL PURPOSES In all studied locations, soil is moderate for all kinds of crops except sensitive ones. Adjacent locations of all industrial areas under study have concentrations of pH, EC, organic carbon, Fe, Cu and Mn are within permissible limits and show good soil quality in most of the studied soil samples taken from vicinal locations of various industrial sites. There is lack of concentrations of Zn is all soil samples and is need to give zinc sulphate fertilizer to compensate this but definite concentrations of P and K in soil samples have been observed at critical limit. Some samples also have higher pH i.e. alkaline in nature and they need to give gypsum for reducing alkalinity from soil samples. CHAPTER 5: WASTEWATER TREATMENT AND SUGGESTIONS The ultimate disposal of wastewater can only be onto the land or into the water. But whenever the watercourses are used for the ultimate disposal, the wastewater is given a treatment to prevent any injury to the aquatic life in the receiving water. Normally, the treatment consists of the removal of suspended and dissolved solids through different units if the treatment plants. The treatment of industrial wastewater may be accomplished in part or as a whole either by the biological processes, as done in the sanitary sewage, or by processes very special for the industrial wastewater only. Depending upon the constituents present in it, the treatment may consist of any one or more treatment (chemical or biological or both) processes. The chemical treatment should be provided only when it becomes unavoidable. The selection of the particular treatment process depends on the effluent requirements and the characteristics of the waste. Today it is not enough to emphasize the protection of the environment. The fundamental purpose of water treatment is to remove impurities that may be offensive or injurious to health and well being of the individual and community. Disinfectant should kill the pathogens quickly at room temperature. It should be inexpensive, and non-toxic, to humans and should provide protection against only contamination in water during conveyance or storage. The Govt. should immediately make laws banning industrial pollution. Failure to do so will lead to substantial penalties and fine. The water treatment plants should be installed in rural areas. The rural inhabitants should try to avoid the use of pesticides in their fields. All small scale and big industries must have anti-pollution unit. Create the awareness about the effects of high concentration of nitrate, fluoride, solids and hardness among villagers. Through strict implementation of the Government’s Water Treatment Programme, water can be rendered safe for drinking. Chapter 1, 2, 3 & 5 precisely details under various heads and chapter 4 details under water for domestic & irrigation purposes and soil for agricultural purposes, results, discussion, tables and graphs of each parameters results, evaluations, assessments and comparison followed by a comprehensive list of relevant references after everything else of the BOOK.

Planet Earth : rocks, life, and history -- The Earth's atmosphere -- Global warming and climate change -- Chemistry of the troposphere -- Chemistry of the stratosphere -- Analysis of air and air pollutants -- Water resources -- Water pollution and water treatment -- Analysis of water and wastewater -- Fossil fuels : our major source of energy -- Nuclear power -- Energy sources for the future -- Inorganic metals in the environment -- Organic chemicals in the environment -- Insecticides, herbicides, and insect control -- Toxicology -- Asbestos -- The disposal of dangerous wastes.

A text for upper undergraduate and graduate level courses in environmental chemistry, chemical engineering, and biology. It deals with natural environmental chemistry processes and pollution; the chemistry process of species, air, water, soil, and the living environment; and hazardous waste and its control. Annotation copyrighted by Book News, Inc., Portland, OR

This introductory text explains the fundamentals of the chemistry of the natural environment and the effects of mankind's activities on the earth's chemical systems. Retains an emphasis on describing how natural geochemical processes operate over a variety of scales in time and space, and how the effects of human perturbation can be measured. Topics range from familiar global issues such as atmospheric pollution and its effect on global warming and ozone destruction, to microbiological processes that cause pollution of drinking water deltas. Contains sections and information boxes that explain the basic chemistry underpinning the subject covered. Each chapter contains a list of further reading on the subject area. Updated case studies. No prior chemistry knowledge required. Suitable for introductory level courses.

This 2nd edition of Understanding Our Environment has been reworked and greatly updated, providing a modern introductory level text for students of pollution and environmental chemistry. The book describes the basic concepts in relation to the chemistry of the atmosphere, freshwaters, oceans and soils, as well as the ways in which pollutants behave in these media (exemplified by case studies based upon topical environmental problems). It also examines the transfer of pollutants between different environmental compartments, the monitoring of the environment, the ecological and human health effects of chemical pollution, economics and regulatory control. Again case studies are used throughout. This unique introductory text is essential reading for students on undergraduate and first year postgraduate courses dealing with pollution and environmental chemistry, as well as for scientists and engineers in industry, public service and consultancy who require a basic understanding of environmental processes.

Pollution and its control are now one of the most serious problems in environmental management, affecting localized areas, regions, and, increasingly, the entire ecosphere. Chemistry and Ecotoxicology of Pollution provides a basic understanding of the chemical, toxicological, and ecological factors involved when major classes of pollutants act on natural systems. The nature and effects of these pollutants are examined from the primary level of their sources and chemical properties, through their interactions in the environment, to their ultimate ecological effects on organisms and ecosystems. Pollutants are divided into groups, with similar properties, and then the chemistry and ecotoxicology of each group is defined. More importantly, in collating and evaluating available information on pollution processes, the book develops unifying theories on the fundamental chemical and ecological nature of pollution processes. The book uses a conceptual framework to evaluate the impact of pollutants on the components and functions of natural ecosystems. It is based on the chemical and physical properties of a pollutant, its environmental behavior and fate, exposure to and toxic effects on organisms, their populations, communities, and responses of affected ecosystems. This sequence can be applied to known, potential, and emerging pollutants of concern. As government initiatives for the control of chemicals take greater effects, pollution research, particularly in ecotoxicology, will be further developed. Chemistry and Ecotoxicology of Pollution helps play an important role in determining the future direction of research activities in environmental management and pollution control on a worldwide scale. It is a basic resource for students (e.g. environmental chemistry, ecology, land and water management, environmental or public health, environmental engineering, and sustainability science), scientists, researchers, policy makers, and professionals in need of a clear understanding of the nature and effects of environmental pollution from an ecological perspective.

Environmental and Ecological Chemistry is a component of Encyclopedia of Chemical Sciences, Engineering and Technology Resources in the global Encyclopedia of Life Support Systems (EOLSS), which is an integrated compendium of twenty one Encyclopedias. The Theme on Environmental and Ecological Chemistry prsents the essential aspects such as: Fundamental Environmental Chemistry; Atmospheric Chemistry; Soil Chemistry; Aquatic Chemistry; Ecological Chemistry; Chemistry of Organic Pollutants Including Agrochemicals. These volumes are aimed at the following five major target audiences: University and College students Educators, Professional practitioners, Research personnel and Policy analysts, managers, and decision makers and NGOs.

Soil and Water Contamination, Second Edition gives a structured overview of transport and fate processes of environmental contaminants. Dealing with all topics essential for understanding and predicting contaminant patterns in soil, groundwater and surface water, it contributes to the formation of a solid basis for adequate soil and water pollution control and integrated catchment management. A unique feature of this work is that it does not treat water and soil pollution as independent processes, but as components of an integrated whole. The core of this geoscientific approach is divided into four parts: • Introduction to the basics of soil and water contamination, such as the fundamentals of environmental pollution and chemistry and the basic properties of soil, groundwater and surface water. • Source, role, and behaviour of substances in soil and water, treating natural and anthropogenic sources of nutrients, heavy metals, radionuclides and organic pollutants as well as emerging substances of concern, their physico-chemical characteristics, behaviour, and toxicity. • Transport and fate of substances in soil and water, focusing on processes of transport, exchange and transformations like advection, dispersion, adsorption kinetics and biochemical decay. Special attention is paid to the mathematical description and modelling of these processes. • Patterns of substances in soil and water, explaining spatial and temporal patterns of pollutants in soil, groundwater, and surface water, illustrated by recent case studies from fundamental and applied research. This comprehensive, successful textbook, now in its second edition, has been conscientiously updated and extended and includes many case studies, examples and exercises sections, providing undergraduate and graduate students in the Earth and Environmental Sciences with all the material necessary for the study of soil and water contamination. In addition, it can serve as a useful source of information for professionals.