Noise In Solid State Devices And Circuits

Gives basic and up-to-date information about noise sources in electronic devices. Demonstrates how this information can be used to calculate the noise performance, in particular the noise figure, of electronic circuits using these devices. Optimization procedures, both for the circuits and for the devices, are then devised based on these data. Gives an elementary treatment of thermal noise, diffusion noise, and velocity-fluctuation noise, including quantum effects in thermal noise and maser noise.

This is the first book dedicated to the next generation of MOSFET models. Addressed to circuit designers with an in-depth treatment that appeals to device specialists, the book presents a fresh view of compact modeling, having completely abandoned the regional modeling approach.Both an overview of the basic physics theory required to build compact MOSFET models and a unified treatment of inversion-charge and surface-potential models are provided. The needs of digital, analog and RF designers as regards the availability of simple equations for circuit designs are taken into account. Compact expressions for hand analysis or for automatic synthesis, valid in all operating regions, are presented throughout the book. All the main expressions for computer simulation used in the new generation compact models are derived.Since designers in advanced technologies are increasingly concerned with fluctuations, the modeling of fluctuations is strongly emphasized. A unified approach for both space (matching) and time (noise) fluctuations is introduced.

Analog CMOS integrated circuits are in widespread use for communications, entertainment, multimedia, biomedical, and many other applications that interface with the physical world. Although analog CMOS design is greatly complicated by the design choices of drain current, channel width, and channel length present for every MOS device in a circuit, these design choices afford significant opportunities for optimizing circuit performance. This book addresses tradeoffs and optimization of device and circuit performance for selections of the drain current, inversion coefficient, and channel length, where channel width is implicitly considered. The inversion coefficient is used as a technology independent measure of MOS inversion that permits design freely in weak, moderate, and strong inversion. This book details the significant performance tradeoffs available in analog CMOS design and guides the designer towards optimum design by describing: An interpretation of MOS modeling for the analog designer, motivated by the EKV MOS model, using tabulated hand expressions and figures that give performance and tradeoffs for the design choices of drain current, inversion coefficient, and channel length; performance includes effective gate-source bias and drain-source saturation voltages, transconductance efficiency, transconductance distortion, normalized drain-source conductance, capacitances, gain and bandwidth measures, thermal and flicker noise, mismatch, and gate and drain leakage current Measured data that validates the inclusion of important small-geometry effects like velocity saturation, vertical-field mobility reduction, drain-induced barrier lowering, and inversion-level increases in gate-referred, flicker noise voltage In-depth treatment of moderate inversion, which offers low bias compliance voltages, high transconductance efficiency, and good immunity to velocity saturation effects for circuits designed in modern, low-voltage processes Fabricated design examples that include operational transconductance amplifiers optimized for various tradeoffs in DC and AC performance, and micropower, low-noise preamplifiers optimized for minimum thermal and flicker noise A design spreadsheet, available at the book web site, that facilitates rapid, optimum design of MOS devices and circuits Tradeoffs and Optimization in Analog CMOS Design is the first book dedicated to this important topic. It will help practicing analog circuit designers and advanced students of electrical engineering build design intuition, rapidly optimize circuit performance during initial design, and minimize trial-and-error circuit simulations.

CMOS: Front-End Electronics for Radiation Sensors offers a comprehensive introduction to integrated front-end electronics for radiation detectors, focusing on devices that capture individual particles or photons and are used in nuclear and high energy physics, space instrumentation, medical physics, homeland security, and related fields. Emphasizing practical design and implementation, this book: Covers the fundamental principles of signal processing for radiation detectors Discusses the relevant analog building blocks used in the front-end electronics Employs systematically weak and moderate inversion regimes in circuit analysis Makes complex topics such as noise and circuit-weighting functions more accessible Includes numerical examples where appropriate CMOS: Front-End Electronics for Radiation Sensors provides specialized knowledge previously obtained only through the study of multiple technical and scientific papers. It is an ideal text for students of physics and electronics engineering, as well as a useful reference for experienced practitioners.

This new book on Analog Circuit Design contains the revised contributions of all the tutorial speakers of the eight workshop AACD (Advances in Analog Circuit Design), which was held at Nice, France on March 23-25, 1999. The workshop was organized by Yves Leduc of TI Nice, France. The program committee consisted of Willy Sansen, K.U.Leuven, Belgium, Han Huijsing, T.U.Delft, The Netherlands and Rudy van de Plassche, T.U.Eindhoven, The Netherlands. The aim of these AACD workshops is to bring together a restricted group of about 100 people who are personally advancing the frontiers of analog circuit design to brainstorm on new possibilities and future developments in a restricted number of fields. They are concentrated around three topics. In each topic six speakers give a tutorial presentation. Eighteen papers are thus included in this book. The topics of 1999 are: (X)DSL and other communication systems RF MOST models Integrated filters and oscillators The other topics, which have been coverd before, are: 1992 Operational amplifiers A-D Converters Analog CAD 1993 Mixed-mode A+D design Sensor interfaces Communication circuits 1994 Low-power low-voltage design Integrated filters Smart power 1995 Low-noise low-power low-voltge design Mixed-mode design with CAD tools Voltage, current and time references vii viii 1996 RF CMOS circuit design Bandpass sigma-delta and other data converters Translinear circuits 1997 RF A-D Converters Sensor and actuator interfaces Low-noise oscillators, PLL's and synthesizers 1998 I-Volt electronics Design and implementation of mixed-mode systems Low-noise amplifiers and RF power amplifiers for telecommunications