Simulations With Nx

This book provides the necessary basics to perform simple to complex simulations with Siemens NX software. It is aimed at designers, CAE engineers and engineering students. Based on NX 9 the following topics are covered in the book: Motion Simulation (MBD), Design Simulation FEA (Nastran), Advanced Simulation (FEA, CFD and EM) and the management of calculation and simulation data (Teamcenter for Simulation). After starting off with brief theoretical introductions each chapter contains learning tasks of increasing difficulty. Most of them are based on the CAD model of the legendary Opel RAK2. The CAD data and calculation results of all exercises can be found online. The exercises can be done in NX versions 8, 8.5, 9, 10 and probably later versions.

Testing and optimizing digital products with Siemens NX and Simcenter 3D In times of Industry 4.0 the digitalization of the value-chain becomes more and more important. The so-called digital twin allows simulations that are very close to reality. This book provides all necessary basics to perform simple as well as complex simulations with NX and Simcenter 3D (former NX CAE). It is aimed at design engineers, CAE engineers and engineering students. The following topics are covered in the book: - Motion Simulation (MBD) - Design Simulation (FEA, Nastran) - Simcenter/Advanced Simulation (FEA, CFD and EM) - Management of Calculation and Simulation Data (Teamcenter for Simulation) Starting off with brief theoretical introductions each chapter contains learning tasks of increasing difficulty. Most of them are based on the CAD model of the legendary Opel RAK2. The presented methods are based on NX 12 and Simcenter 3D, the new 3D CAE solution. Revised topics in this edition are Motion Simulation with the new Simcenter Motion solver and post-processing in Simcenter 3D (FEA). The CAD data and calculation results of all exercises can be found online. The exercises can be completed in NX 11, NX 12 and probably later versions.

In times of Industry 4.0 the digitalization of the value-chain becomes more and more important. The so-called digital twinallows simulations that are very close to reality. This book provides all necessary basics to perform simple as well as complex simulations with NX and Simcenter 3D (former NX CAE). It is aimed at design engineers, CAE engineers and engineering students. The following topics are covered in the book: -Motion Simulation (MBD) -Design Simulation (FEA, Nastran) -Simcenter/Advanced Simulation (FEA, CFD and EM) -Management of Calculation and Simulation Data (Teamcenter for Simulation) Starting off with brief theoretical introductions each chapter contains learning tasks of increasing difficulty. Most of them are based on the CAD model of the legendary Opel RAK2. The presented methods are based on NX 12 and Simcenter 3D, the new 3D CAE solution. Revised topics in this edition are Motion Simulation with the new Simcenter Motion solver and post-processing in Simcenter 3D (FEA). The CAD data and calculation results of all exercises can be found online at www.drbinde.de/index.php/en/204. The exercises can be completed in NX 11, NX 12 and probably later versions.

This book provides the necessary basics to perform simple to complex simulations with Siemens NX software. It is aimed at designers, CAE engineers, and engineering students. Based on NX 9 the following topics are covered in the book: Motion Simulation (MBD), Design Simulation FEA (Nastran), Advanced Simulation (FEA, CFD and EM) and the management of calculation and simulation data (Teamcenter for Simulation). Starting with brief theoretical introductions, each chapter contains learning tasks of increasing difficulty. Most of them are based on the CAD model of the legendary Opel RAK2. The CAD data and calculation results of all exercises can be found online. The exercises can be done in NX versions 8, 8.5, 9, 10 and probably later versions.

This book provides the necessary basics to perform simple to complex simulations with Siemens NX software. It is aimed at designers, CAE engineers and engineering students. Based on NX 9 the following topics are covered in the book: Motion Simulation (MBD), Design Simulation FEA (Nastran), Advanced Simulation (FEA, CFD and EM) and the management of calculation and simulation data (Teamcenter for Simulation). After starting off with brief theoretical introductions each chapter contains learning tasks of increasing difficulty. Most of them are based on the CAD model of the legendary Opel RAK2. The CAD data and calculation results of all exercises can be found online. The exercises can be done in NX versions 8, 8.5, 9, 10 and probably later versions. Dr.-Ing. Peter Binde is managing director of the company Dr. Binde Engineers and lecturer on FEM at RheinMain University of Applied Sciences, department of mechanical engineering. He is a globally active specialist for product simulation with NX. Prof. Dr.-Ing. Reiner Anderl is head of the department of Computer Integrated Design at the faculty of engineering at TU Darmstadt (DiK).

This book illustrates numerical simulation of fluid power systems by LMS Amesim Platform covering hydrostatic transmissions, electro hydraulic servo valves, hydraulic servomechanisms for aerospace engineering, speed governors for power machines, fuel injection systems, and automotive servo systems It includes hydrostatic transmissions, automotive fuel injection, hydropower speed units governor, aerospace servo systems along with case studies of specified companies Aids in predicting and optimizing the static and dynamic performances related to the systems under study

The primary goal of Parametric Modeling with NX 12 is to introduce the aspects of designing with Solid Modeling and Parametric Modeling. This text is intended to be used as a practical training guide for students and professionals. This text uses NX 12 as the modeling tool, and the chapters proceed in a pedagogical fashion to guide you from constructing basic solid models to building intelligent mechanical designs, creating multi-view drawings and assembly models. This text takes a hands-on, exercise-intensive approach to all the important Parametric Modeling techniques and concepts. This textbook contains a series of fourteen tutorial style lessons designed to introduce beginning CAD users to NX. This text is also helpful to NX users upgrading from a previous release of the software. The solid modeling techniques and concepts discussed in this text are also applicable to other parametric feature-based CAD packages. The basic premise of this book is that the more designs you create using NX, the better you learn the software. With this in mind, each lesson introduces a new set of commands and concepts, building on previous lessons. This book does not attempt to cover all of NX’s features, only to provide an introduction to the software. It is intended to help you establish a good basis for exploring and growing in the exciting field of Computer Aided Engineering. This book also introduces you to the general principles of 3D printing including a brief history of 3D printing, the types of 3D printing technologies, commonly used filaments, and the basic procedure for printing a 3D model. 3D printing makes it easier than ever for anyone to start turning their designs into physical objects, and by the end of this book you will be ready to start printing out your own designs.

This book systematically introduces the development of simulation models as well as the implementation and evaluation of simulation experiments with Tecnomatix Plant Simulation. It deals with all users of Plant Simulation, who have more complex tasks to handle. It also looks for an easy entry into the program. Particular attention has been paid to introduce the simulation flow language SimTalk and its use in various areas of the simulation. The author demonstrates with over 200 examples how to combine the blocks for simulation models and how to deal with SimTalk for complex control and analysis tasks. The contents of this book ranges from a description of the basic functions of the material flow blocks to demanding topics such as the realization of a database-supported warehouse control by using the SQLite interface or the exchange of data by using XML, ActiveX, COM or DDE.